Visit our website for helpful 3D model files and assembly videos.
 
www.guillow.com/3Dassembly.aspx
KIT 4505
STUNT FLYER
COPYRIGHT 2013 BY PAUL K. GUILLOW, INC.
You will build the wing frames directly over layouts. To ensure that they are built straight, tape this sheet on a flat surface and tape parts down as shown. If you have a workboard you can exchange the tape for common pins to hold parts down.
First carefully remove all laser cut parts from the balsa sheets. Use white glue (or with adult supervision a fast drying glue like super glue) for assembling your model. Glue can be purchased at your local hobby or hardware store.
NOTE: This model will fly well with one loop of rubber thread, but if you want to give it more speed / climb try two  loops of rubber motor. (You have enough rubber to make & fly both options.)
FLIGHT INSTRUCTIONS
Check the balance of your model by putting your fingertips under the wing at the balance point (approx ½” back from the leading edge) and picking up, the airplane should hang level or slightly nose heavy.  Use the stick on weights included in the kit to achieve this.  Test glide model before making powered flights, hold model beneath wing and launch gently forward into any breeze.  If plane noses up or dives into ground add or subtract some weight.  After proper corrections, wind motor clockwise about 100 to 125 turns and launch straight.  Model can be flown in a gym or outside on a calm day.
KIT 4505
WING FRAME LAYOUT SHEET
Terms and notes to know on Wing Layouts
FRONT VIEW
RIGHT WING
LEFT WING
LEADING EDGE
W8 - CENTER SPAR
TRAILING EDGE
END VIEW
(Before dihedral is added)
WING RIBS
NOTE: SLANT - FOR WING DIHEDRAL (The angle needed to give the plane stability)
COVERING WING FRAMES
Cut out decals just inside the outer edge lines.
BUILDING WING FRAMES
Tape
1. Tape W1 - W3 over right wing on plan and glue together.
2. Glue W4 - W6 ribs into slots on the leading and trailing edges.
3. Slide W8 center spar down into slots and glue into place.
4. Glue W7 rib in place, making sure it butts up to W8.
5. Let dry and repeat for left wing.
3. Wrap flaps over leading and trailing edges and press down.
1. Place the bottom decal, sticky side up, on your work surface and align the +s  with  the  wing ribs. Press down.
4. Repeat on other wing.
2. Line the +s on top decal up with where the wing ribs and center keel meet.
ASSEMBLING THE MODEL
1.  Glue one nose brace onto the front of the fuselage.
2.  Glue the tube of the propeller unit into the nose of the fuselage (Be sure not to get glue on the prop wire).
3.  Glue the other nose brace on the other side of the fuselage, securing the propeller unit into place.
4.  Glue canopy onto the fuselage.
5.  Cut and glue wire for rear motor mount into slot.
6.  Glue stabilizer on the fuselage. When dry, glue rudder on the stabilizer. Be careful to get them straight.
7.  Glue assembled wings into the slots on fuselage. Hold until dry. Check wing angle from front of the model.
8.  Loop rubber band motor around rear wire and propeller hook.  Tie knot.  (See note)
9.  Assemble and install landing gear, if desired (see note).  Be careful to build one left and one right assembly.
FULL SIZE SIDE VIEW
POINT OF BALANCE
REAR MOTOR MOUNT WIRE
CANOPY
FUSELAGE
PROPELLER UNIT
PROPELLER TUBE
NOSE BRACE
LANDING GEAR ASSEMBLY
RUDDER
STABILIZER
PERSPECTIVE VIEW
NOTE: If you would like to build a lighter & better flying model, build it without the landing gear.
LANDING GEAR ASSEMBLY
W6
WHEEL STRUT
WIRE
WHEEL
Glue landing gear to wing up through W3 slot.
Bend landing gear wire and assemble landing gear. Cut off the extra wire with wire cutters.
FUSELAGE
FRONT VIEW
NOSE BRACE
LEFT WING
STABILIZER
RUDDER
NOSE BRACE
CANOPY
POINT OF BALANCE
RIGHT WING
www.guillow.com/3Dassembly.aspx
POINT OF BALANCE